What Does It Cost to Fix a Leaking Shower Pan?

It depends on where the water is getting in. If it is coming through a cracked sealant joint at the curb, a corner, or around a pipe, a targeted repair from above can often stop it for a modest cost. If the pan itself has failed, the waterproof layer under the floor tile, the reliable fix is removing the shower floor tile and rebuilding the pan. National cost guides put a custom tile shower pan at about $900 to $3,500 (This Old House, 2026) and a typical shower pan installation at about $1,536 to $2,967 (Homewyse, 2026), before any repairs to water damage underneath.
What is a shower pan?
In a tiled shower, the pan is the sloped, waterproof base under the floor tile that carries water to the drain. The tile and grout on top are not waterproof on their own. Water soaks through grout over time, and the pan is what catches it and sends it down the drain. When the pan cracks, separates at the drain, or was never fully waterproofed, water escapes into the floor and walls instead.
How can you tell if a shower pan is leaking?
The clearest signs show up outside the shower: a stain, soft spot, or bubbling paint on the ceiling below, a persistent musty smell, or flooring next to the shower that has lifted or darkened. Inside the shower, look for grout on the floor that stays dark long after showering, tiles that sound hollow or move underfoot, or a floor that has started to crack or sink near the drain. Leaks at the drain body or the shower valve are plumbing repairs, so a good diagnosis separates those from a pan failure before any tile comes out.
How do you test a shower pan for leaks?
The usual check is a flood test: the drain is plugged, the shower floor is filled with a little water, and the level is marked to see whether it drops. A falling water line points to a leak in the pan or at the drain connection, but it does not show exactly where the water is escaping. Because water may also be coming from the valve, the drain body, or a joint in the walls, it is worth having the shower looked at before deciding the pan has failed.
Can a leaking shower pan be repaired without removing tile?
Sometimes. If the water is getting in through a failed caulk joint at the curb or an inside corner, a cracked grout line at a change of plane, or a gap around a pipe, those can often be fixed without disturbing the floor. If the waterproof layer of the pan has failed, there is no reliable way to fix it from above, because it sits under the tile. Coatings and sealers on top of the tile may slow a leak for a while, but they do not repair the pan.
What does replacing a shower pan involve?
The shower floor tile comes up, usually along with the bottom row of wall tile so the new waterproofing can tie into the walls. The old pan is removed, and the subfloor and framing are checked for water damage and repaired. A new sloped pan is built, waterproofed, and tested by filling it with water and checking for leaks before any tile goes down. Then the floor is tiled and grouted, and each layer is given time to cure before the shower is used again.
How much does it cost to fix a leaking shower pan?
A targeted sealant or grout repair at the source of a leak is the least expensive fix, when that is truly where the water is getting in. Replacing the pan costs more. National guides put a custom tile shower pan at about $900 to $3,500 and removing an old pan at about $250 (This Old House, 2026), and a typical installation at about $1,536 to $2,967 per pan (Homewyse, 2026). Prefab acrylic or fiberglass pans cost less, roughly $150 to $620 for the pan, but they replace the tile floor rather than sit under it. Rot or mold in the framing below adds to any of these. See the tile section of our cost guide for related ranges.
What happens if you ignore a leaking shower pan?
The water keeps going into the floor and walls every time the shower runs. Over time that can rot the subfloor and framing, damage the ceiling below, and grow mold, which turns a pan replacement into a larger repair. Regrouting over a failed pan only hides the problem for a while. See how to tell if a shower is leaking behind the tile on our shower tile repair page, or contact us for a free estimate. If the diagnosis is a full rebuild, that work is covered under shower tile installation.
Frequently Asked Questions
How much does it cost to replace a shower pan?
National cost guides put a custom tile shower pan at about $900 to $3,500 (This Old House, 2026) and a typical installation at about $1,536 to $2,967 per pan (Homewyse, 2026). Removing the old pan adds roughly $250, and repairs to water damage underneath are extra.
Can you fix a leaking shower pan without removing the tile?
Only when the water is getting in somewhere other than the pan itself, such as a failed caulk joint at the curb, a cracked corner, or a gap around a pipe. If the pan's waterproof layer has failed, the floor tile has to come up so the pan can be rebuilt.
How do I know if my shower pan is leaking?
Look for a stain or soft spot on the ceiling below, a musty smell, lifted flooring next to the shower, or floor grout that stays dark long after showering. Hollow or moving floor tiles and cracking near the drain are also common signs.
Will regrouting stop a shower pan leak?
No. Grout is not waterproof, and the pan underneath is what keeps water out of the floor. New grout over a failed pan may look fine for a while, but the leak continues underneath.
Need Professional Help?
If you've identified masonry issues or need a professional inspection, Grand Rapids Masonry & Restoration is here to help. We serve the Grand Rapids metro area and surrounding communities.
Related Articles

Should You Regrout Shower Tile or Rebuild the Shower?
Regrouting shower tile is worth it when the tile is sound and the waterproofing is intact. When grout keeps reopening or there is a stain below the shower, the problem is usually behind the tile — not in the grout.

How Much Does a Walk-In Tile Shower Cost?
National cost guides put a tiled walk-in shower at roughly $8,000 to $13,000 for a midrange build. Here is what goes into that price, what pushes it higher, and how tile compares with a prefab kit.

How Much Does Tile Floor Installation Cost?
National cost guides put a complete tile floor at roughly $15 to $75 per square foot, and our own approximate range is $20 to $60 installed. Here is what goes into the price, what pushes it higher, and how to compare estimates.
Tile Services in Greater Grand Rapids
Grand Rapids Masonry & Restoration handles indoor tile work year-round — showers, floors, backsplashes, repair, and replacement across the Grand Rapids metro.
View all tile contractor services →